A rectangle in the ratio 1:√2 keeps its shape when you cut it in half across the long side, and no other ratio does. That property is why the A4 paper ratio is the square root of 2. Half of an A4 sheet has the shape of A5, and two A4 sheets side by side have the shape of A3.
The A4 paper size itself is 210 × 297 mm, which is 21 × 29.7 cm. The size is set by ISO 216:2007, the paper size standard of the ISO (International Organization for Standardization).
In inches, A4 is about 8.27 × 11.69. The standard takes √2 (about 1.414) as the theoretical ratio of long side to short side and rounds the sizes to whole millimeters. A0, the base size of the series, has a defined area of one square meter.
Why √2 is the only ratio that survives halving
The √2 ratio of the A series is the only aspect ratio that a rectangle keeps after being cut in half. ISO 216 builds the system on two rules, as the standard's preview pages show. Each size is the next larger size divided in two, parallel to its shorter side, and all sizes are geometrically similar. You can find the ratio that meets both rules in four steps:
- Take a sheet with a short side of 1 and a long side of r. Its ratio is r.
- Cut it at the middle of the long side, parallel to the short side. Each half measures 1 by r/2.
- If r is 2 or less, the half has a long side of 1 and a short side of r/2, so the new ratio is 1 ÷ (r/2) = 2/r. If r is above 2, the long side stays r/2 and the ratio becomes r/2, which can never equal r.
- For the shape to stay the same, r must therefore equal 2/r. That gives r² = 2 and r = √2 ≈ 1.414.
In the words of ISO 216, this is the ratio between the side and the diagonal of a square. A square with a side of 1 has a diagonal of √2. An A-series sheet relates its short side to its long side the same way.
A sheet with a ratio between 1 and 2 flips between two values, because each cut produces 2/r. A strip with a ratio above 2 is first halved toward that range. The table runs the calculation for a few starting ratios, in generic units that can be centimeters or inches.
| Starting ratio (long ÷ short) | Sides | Halved once | Halved twice |
|---|---|---|---|
| 1.500 | 2 × 3 | 1.333 (1.5 × 2) | 1.500 (1 × 1.5) |
| 1.333 | 3 × 4 | 1.500 (2 × 3) | 1.333 (1.5 × 2) |
| 2.000 | 1 × 2 | 1.000 (1 × 1, a square) | 2.000 (0.5 × 1) |
| 4.000 | 1 × 4 | 2.000 (1 × 2) | 1.000 (1 × 1, a square) |
| 1.414 (√2) | 1 × 1.414 | 1.414 (0.707 × 1) | 1.414 (0.5 × 0.707) |
The last row shows the √2 ratio, with values rounded to three decimals. For other ratios between 1 and 2, the halves alternate between a longer, thinner shape and a squarer one. Only √2 gives the same shape every time. That is why a round size such as 20 × 30 cm cannot be part of the A series.
The 1:√2 proportion is also called the Lichtenberg ratio, and it is sometimes confused with the golden ratio (about 1.618). Cambridge computer scientist Markus Kuhn points out the difference in his overview of ISO paper sizes. A golden rectangle keeps its shape when you cut a square off it. A √2 sheet keeps its shape when you cut it in half, which is the property that helps in an office.
Why A0 is one square meter
A0 is defined in ISO 216 as having an area of 1 m². DIN (Deutsches Institut für Normung), the German standards body, published a history of its paper formats. It names the key step: tying the system to the meter through area, not side length. Kuhn explains why: two sides in a √2 ratio cannot both be round metric numbers, so the round value goes to the area.
Call the short side x. The long side is then √2·x. Solving x · √2·x = 1 m² gives a short side of 0.8409 m and a long side of 1.1892 m. In meters, the long side is the fourth root of 2, which a scientific calculator gives in one step.
ISO 216 rounds those values to whole millimeters and lists A0 as 841 × 1,189 mm. The rounded A0 is only 51 mm² short of a full square meter. You can confirm it by entering the sides in the square meter calculator.
A round area also shortens the paper weight calculation. Paper is sold by grammage, its weight per square meter. An A4 sheet has a theoretical area of 1/16 m², so on 80 g/m² paper it weighs about 5 g, the same example Kuhn gives.
ISO 216 sizes from A0 to A10
The A series paper sizes below come from the table in ISO 216:2007, where they are given in millimeters. Inches are millimeters divided by 25.4 and rounded to two decimals, and centimeters are one tenth of the millimeter value. The last column shows each size's area relative to A0.
| Size | mm | Inches | cm | Theoretical area (relative to A0) |
|---|---|---|---|---|
| A0 | 841 × 1,189 | 33.11 × 46.81 | 84.1 × 118.9 | 1 (1 m²) |
| A1 | 594 × 841 | 23.39 × 33.11 | 59.4 × 84.1 | 1/2 |
| A2 | 420 × 594 | 16.54 × 23.39 | 42.0 × 59.4 | 1/4 |
| A3 | 297 × 420 | 11.69 × 16.54 | 29.7 × 42.0 | 1/8 |
| A4 | 210 × 297 | 8.27 × 11.69 | 21.0 × 29.7 | 1/16 |
| A5 | 148 × 210 | 5.83 × 8.27 | 14.8 × 21.0 | 1/32 |
| A6 | 105 × 148 | 4.13 × 5.83 | 10.5 × 14.8 | 1/64 |
| A7 | 74 × 105 | 2.91 × 4.13 | 7.4 × 10.5 | 1/128 |
| A8 | 52 × 74 | 2.05 × 2.91 | 5.2 × 7.4 | 1/256 |
| A9 | 37 × 52 | 1.46 × 2.05 | 3.7 × 5.2 | 1/512 |
| A10 | 26 × 37 | 1.02 × 1.46 | 2.6 × 3.7 | 1/1024 |
Each row comes from cutting the row above it across its long side. The short side of one size becomes the long side of the next. A4 is A0 halved four times, with a theoretical area of 1/16 m².
The inch figures rely on the inch being exactly 25.4 mm. For other units, the length converter does the conversion.
ISO 216 also lists two rarely used oversizes as part of the series: 2A0 (1,189 × 1,682 mm) and 4A0 (1,682 × 2,378 mm). The values are trimmed sheet sizes. A printer's printable area and a print shop's bleed margin do not change the size of the paper.
The standard covers paper for administrative, commercial and technical use, plus printed matter such as forms and catalogs. According to ISO, it does not necessarily apply to newspapers, published books or posters.
Why A4 is 210 × 297 mm instead of exactly √2
The odd-looking 29.7 cm side of A4 is what you get when the √2 ratio is rounded to whole millimeters. In Kuhn's program that computes the A series, A0 is rounded to the nearest millimeter. Every smaller size then halves the long side and drops the result to the next lower whole millimeter.
Rounding down guarantees that two smaller sheets placed side by side are never larger than the sheet above them. Starting from 841 × 1,189 mm, halving the long side at each step and rounding down produces all eleven sizes in the table.
For example, half of A4's 297 mm long side is 148.5 mm. That is why the short side of A5 is 148 mm.
The effect of rounding on the ratio varies from size to size. In the table, the theoretical size keeps the sides at exactly √2 and is shown rounded to two decimals. The actual ratio divides the ISO long side by the ISO short side.
| Size | ISO size (mm) | Theoretical size (mm) | Actual ratio | Deviation from √2 (%) |
|---|---|---|---|---|
| A0 | 841 × 1,189 | 840.90 × 1,189.21 | 1.4138 | −0.03 |
| A1 | 594 × 841 | 594.60 × 840.90 | 1.4158 | +0.11 |
| A2 | 420 × 594 | 420.45 × 594.60 | 1.4143 | +0.005 |
| A3 | 297 × 420 | 297.30 × 420.45 | 1.4141 | −0.005 |
| A4 | 210 × 297 | 210.22 × 297.30 | 1.4143 | +0.005 |
| A5 | 148 × 210 | 148.65 × 210.22 | 1.4189 | +0.33 |
| A6 | 105 × 148 | 105.11 × 148.65 | 1.4095 | −0.33 |
| A7 | 74 × 105 | 74.33 × 105.11 | 1.4189 | +0.33 |
| A8 | 52 × 74 | 52.56 × 74.33 | 1.4231 | +0.63 |
| A9 | 37 × 52 | 37.16 × 52.56 | 1.4054 | −0.62 |
| A10 | 26 × 37 | 26.28 × 37.16 | 1.4231 | +0.63 |
For A4 the deviation stays at 0.005%, far too small to see with a ruler. On small sizes one millimeter is a bigger share of each side, so the deviation grows to about 0.6% for A8 and A10.
In lowest terms, the A4 ratio is 99:70. That fraction is one of the approximations of √2 produced by its continued fraction. Here it is a by-product of the rounding rule that starts at A0. Entering the two sides in the aspect ratio calculator shows the reduced ratio.
Your own A4 sheet may still measure a millimeter or two off. Kuhn's summary of ISO 216 gives a tolerance of ±2 mm for sides between 150 and 600 mm. Both sides of A4 fall in that range, so a difference of up to 2 mm per side is within the standard.
How US Letter compares
US Letter is the 8.5 × 11 inch sheet widely used in the United States and Canada, and it sits outside the A series. The table puts the two sizes side by side, and the half row gives each sheet cut in two across its long side.
| Property | A4 | Letter |
|---|---|---|
| Size (mm) | 210 × 297 | 215.9 × 279.4 |
| Size (inches) | 8.27 × 11.69 | 8.5 × 11 |
| Ratio (long ÷ short) | 1.414 | 1.294 |
| Physical half | 148.5 × 210 mm, ratio 1.414 | 5.5 × 8.5 in, ratio 1.545 |
| Area | 0.0624 m² | 0.0603 m² |
Standard A5 is rounded to 148 × 210 mm, which gives it a ratio of 1.419.
Letter's ratio flips between 1.294 and 1.545 each time the sheet is halved. Kuhn notes that this is why scaling between US sizes leaves an empty margin.
A4 is 5.9 mm narrower and 17.6 mm taller than Letter. Kuhn adds that a document laid out for A4 often cannot be printed on Letter without losing content or reformatting.
What the ratio does on a copier
Between any two neighboring A sizes the scale factor is always the same: √2 to enlarge and 1/√2 to reduce. The 141 and 71 settings on copiers are those two values rounded. Kuhn notes that most copiers have a preset button for reducing A3 to A4. Two facing A4 pages in an open magazine form an A3, and at that scale they shrink to about one A4 sheet.
| Operation | Scale | Result |
|---|---|---|
| A4 → A3 | 141% (setting close to √2) | The page grows to about A3 size |
| A3 → A4 | 71% (setting close to 1/√2) | Two facing A4 pages shrink to about one A4 |
| A4 → A5 | 71% (setting close to 1/√2) | The page drops to about half the area |
| A3 → A5 | 50% | Two reduction steps |
| A5 → A3 | 200% | Two enlargement steps |
At the exact 1/√2 scale, an A3 page shrinks to 210.01 × 296.98 mm and fits A4 almost perfectly.
At the rounded 71 setting, the image is 210.87 × 298.20 mm, which overshoots A4 by about 1 mm per side. Keep that in mind when content runs close to the edge, and use the percentage calculator to turn another scale factor into a copier setting. The ratio calculator finds the scale between any two sizes.
When an in-between size is needed, ISO 216 defines the B series. Each B size is the geometric mean of the two neighboring A sizes. B4 (250 × 353 mm), for example, sits between A4 and A3.
Where the A series came from
The idea behind the A series is more than two centuries old. The main milestones:
- 1786: Georg Christoph Lichtenberg, a physics professor in Göttingen, wrote to Johann Beckmann on October 25, 1786. He said that for all folded formats to be similar, the short side must relate to the long side as 1:√2. According to the text of the letter, after setting this as a problem for a student, he found the paper he was writing on already had that ratio.
- 1911–1913: According to DIN's history, the Nobel Prize-winning chemist Wilhelm Ostwald required a "world format" (Weltformat) series whose sizes halve into each other and stay similar. He found that a 1:√2 ratio meets that requirement.
- 1922: The system developed by Walter Porstmann, Ostwald's former assistant and secretary, was published as DIN 476 "Papierformate" on August 18, 1922.
- 1975: The principles and sizes of the A and B series became an international standard as ISO 216.
- 2007: The second edition, ISO 216:2007, was published. According to ISO, it was reviewed and confirmed in 2021 and entered a new systematic review on July 15, 2026 (status as of November 7, 2026).






